2.4GHz 3.2dBi RP-SMA Male Omni Antenna for WiFiThis 2.4GHz 3.2dBi RP-SMA Male Omni antenna is intended for use for all 2.4GHz applications. The antenna is fitted with an RP-SMA male connector and a blade, made of a flexible material that can be rotated 360 degrees. Suitable for telemetry and WIFI tr..
40pin Prototype Pi board Prototyping Pi Plate for Raspberry Pi 3/4BFeatures :Raspberry Pi terminal to provide the IO, port connection.3.81 posts quality, reliable, convenient, durable.Combined with the Proto Shield, the middle can be used as a prototype expansion board.Double-sided PCB Prototyping e..
DIY Proto HAT Shield for Raspberry Pi 3 /4BFeatures:Prototyping HAT for Raspberry PiCompatible with Raspberry Pi A+/ B+/Pi 2/Pi 3/Zero/Zero WThe proper label of Raspberry Pi GPIO and PowerComes with mounting screws, nuts, and spacerSoldering is required..
LCD1602 RGB LCD HAT with Keypad For Raspberry PIFeaturesIt’s an LCD display which can show two lines and 16 characters on it. and it easy to use a blue and white 16×2 Character LCD.It’s based on I2c protocol and it can communicate with your Pi with less wire.With this in mind, we wanted to make it e..
PI ZERO/ZERO W ENC28J60 Internet Module Supporting all RPI BoardFeatures :Fully Compatible with 10/100/1000Base-T NetworksIntegrated MAC and 10Base-T PHYSupports One 10Base-T Port with Automatic Polarity Detection and CorrectionSupports Full and Half-Duplex modesAutomatic Programmable Retransmit on ..
Power Over Ethernet (PoE) HAT for Raspberry Pi 3 B+ ModelFeatures:Power over Ethernet (PoE) 802.3af CompliantClass 2 DeviceFully Isolated Switched-Mode Power Supply (SMPS)Input Voltage: 36V – 56VOutput Voltage: 5VOutput Current: Up to 2.5AIntegrated Fan Control and 25mm x 25mm Brushless FanPlug-and-..
Raspberry Pi GPIO UART HAT / Shield V1.0Features:Onboard Power Indicator LampOnboard Infrared Receiving FunctionGPIO Expansion Function:1. 16 independent GPIO with power and ground (3.3V level)2. 2 Independent SPI expansion interface and 1 I2C expansion interface3. 1 standard RS232 serial port: can ..
SeeedStudio Grove AI HAT for Edge ComputingFeatures:CPU: K210 RISC-V Dual Core 64bit, 400Mh(Max. 600Mhz)FPU: IEEE754-2008 compliant high-performance pipelined FPUKPU(Neural Network Processor ): 1.Supports the fixed-point model that the mainstream training framework trains according to specific restr..
SmartElex 10D DC Motor Driver HAT for Raspberry PiFeatures:Wide 6V to 28V motor Operating Voltage.Continuous 10A maximum current without Heatsink and 30A peak current for 10 seconds.Two brushed DC motor Bidirectional control.Current limiting at 35A.PWM frequency up to 32KHzSupport TTL PWM from the m..
SmartElex GPS HAT for Raspberry PiFeatures:High sensitivity: -167dBm @Tracking, -149dBm @Acquisition.The multi-GNSS engine for GPS, GLONASS, Galileo, and QZSS99 acquisition channels, 33 tracking channels.Balloon mode, for high altitude up to 80km.Only 26mA current draw.PPS VS. NMEA can be used for t..
Stepper Motor HAT V2.0 Shield for Raspberry Pi Zero/3B+/4BFeatures:Support 2CH IIC Communication Interface.1CH I2C compatible with 5V for other controllers.4Bit Programmable address support 16pcs in series.Support 16bit PWM output.12Bit Resolution.PWM maximum frequency 50KHz.Support 4CH servo motor ..
VGA666 RPI Dtoverlays ModuleFeaturesSupport for Raspberry Pi A+, Raspberry Pi B+, Raspberry Pi Zero, Raspberry Pi 2, model B, Raspberry Pi 3 Model BThe VGA output supports resolution: from 800x600 up to 30fps.With 6 bits per channel, you have a maximum of 262144 colors.Easy to setup.Easy to configur..